Basic Construction And Carpentry Techniques Home







Google





MISSION FURNITURE

HOW TO MAKE IT

PART TWO


POPULAR MECHANICS HANDBOOKS


CHICAGO

POPULAR MECHANICS COMPANY

Copyrighted, 1910 By H. H. WINDSOR

AN OAK BEDSTEAD



Oak Bedstead Complete

The accompanying sketches show an artistic design for a mission bed, so simple in construction and design that most any one that has a few tools and a knowledge of their use can make it. It is best made of quarter-sawed oak, as this wood is the easiest to procure and work up and looks well with any finish. If the stock is ordered from the mill ready cut to length, squared and sanded, much of the hard labor will be saved.

The following is a list of the material needed:

Square up the four posts in pairs and lay out the mortises as per drawing. To do this, lay them side by side on a flat surface with the ends square and mark them with a try-square. The tenons on the end rails are laid out in the same manner as the posts. Four of the end rails should be marked and mortises cut for the upright slats as shown in the detail drawing. The tenons on the end rails are about 1 in. long, while those on the slats can be 3/4 in. long. Fit all the parts together before gluing to see that they fit square and tight. After the glue has been applied clamp them together perfectly square and set them away to dry. They should dry at least twenty-four hours before the clamps are removed.



Details of Oak Bedstead

While the ends are drying, the side rails can be made. These have a 1-in. square cleat screwed to the inner side for the slats to rest upon. If springs are used, five slats will be sufficient. They can be placed where the springs will rest upon them. After the position of the slats has been located, nail small blocks at their sides to hold them in place. For fastening the side rails to the posts, patent devices can be purchased at a local hardware store. The posts will have to be mortised to receive these, and care should be exercised to get them in the right place.

When the bed is complete go over it carefully and scrape all the surplus glue from about the joints, as the finish will not take where there is any glue. Remove all rough spots with fine sandpaper; then apply the stain you like best, which may be any of the many mission stains supplied by the trade for this purpose. If this bed is well made and finished, it will be an ornament to any home.


Mission Furniture

  1. AN OAK BUFFET
  2. OAK STAIN
  3. A PLAIN OAK HALL CLOCK
  4. A ROCKING CHAIR
  5. A CURVED BACK ARM CHAIR
  6. A PLATE RACK
  7. TOOL FOR MARKING DOWEL HOLES
  8. A MAGAZINE TABLE
  9. A WASTE PAPER BASKET
  10. AN OAK WRITING DESK
  11. AN OAK COUCH WITH CUSHIONS
  12. ELECTRIC SHADE FOR THE DINING ROOM
  13. HOW TO BEND WOOD
  14. A SMOKING STAND
  15. A CHINA CLOSET
  16. A LEATHER-COVERED FOOTSTOOL
  17. ARTS-CRAFTS MANTEL CLOCK
  18. A MUSIC STAND
  19. MAKING SCREWS HOLD IN THE END GRAIN OF WOOD
  20. A WALL CASE WITH A MIRROR DOOR
  21. A SIDE CHAIR
  22. AN ARM CHAIR
  23. A BOOKCASE
  24. A LAMP STAND
  25. AN EXTENSION DINING TABLE
  26. AN OAK-BOUND CEDAR CHEST
  27. A TOOL FOR MAKING MORTISES
  28. A DRESSER FOR CHILD'S PLAYROOM
  29. CUTTING TENONS WITH A HAND-SAW
  30. ARTS AND CRAFTS OIL LAMP
  31. ANOTHER CHINA CLOSET
  32. AN OAK BEDSTEAD
  33. AN OAK FOOTSTOOL
  34. A LIBRARY SET IN PYRO-CARVING
  35. A GRILLE WITH PEDESTALS TO MATCH
  36. A LADY'S WRITING DESK
  37. A TELEPHONE STAND AND STOOL
  38. HOW TO MAKE A DOWEL-CUTTING TOOL
  39. A MEDICINE CABINET




                                                                
Basic Construction And Carpentry Techniques Home







Google




Written and maintained by
Ronald Hunter
           
  All images and text are copyright Ronald Hunter 2005, 2006, 2007 & 2008.
  All rights reserved
Top